Delivery in 11 to 15 business days. Save more on bulk orders. Free US and worldwide shipping. Get an instant quote

Home / Blog / How to sew on a patch by hand: a step-by-step guide

3 min read

How to sew on a patch by hand: a step-by-step guide

A clean, permanent, wash-proof way to attach any patch with a needle and thread, with the mistakes to avoid on jackets, jeans and bags.

Sewing a patch onto a jacket by hand with needle and thread

Sewing is the most permanent way to attach a patch. It survives hot washes, hard use and years of wear, which is why it is the standard choice for uniforms, work jackets and anything you plan to keep. You do not need to be good at sewing. You need a needle, thread and about ten minutes.

What you need

  • The patch, ideally a sew-on embroidered patch or woven patch
  • A sharp hand-sewing needle (size 7 to 9 works for most fabrics)
  • Thread that matches the patch border, or the garment if you want it hidden
  • Straight pins or a small dab of fabric glue to hold the patch still
  • Scissors

Step 1: Place and pin the patch

Lay the garment flat and put the patch exactly where you want it. Check it with the garment on if you can, because a patch that looks centered on the table can sit crooked on a body. Pin it at four points, one on each side. On thick fabric such as denim or canvas, push the pins through from the front so they do not poke you later.

Step 2: Thread the needle

Cut about 20 inches of thread. Longer than that and it tangles. Thread the needle and tie a firm knot at the end. For extra strength on jackets and bags, use a doubled thread.

Step 3: Start from the inside

Bring the needle up from the underside of the fabric and through the very edge of the patch, close to the border. Starting from inside hides the knot.

Step 4: Use a whipstitch or a backstitch

The whipstitch is the easiest. Push the needle down through the garment right beside the patch edge, then bring it back up about an eighth of an inch further along, catching the patch border each time. Keep the stitches even and not too tight, or the fabric will pucker.

For a stronger hold, use a backstitch just inside the border. It looks like a line of tiny stitches and is almost impossible to pull out.

Step 5: Go all the way around

Work around the whole edge, removing pins as you reach them. Corners need two stitches close together so they do not lift. On large patches, such as a jacket back, add a few stitches through the middle so the center does not bubble.

Step 6: Finish and lock the thread

Push the needle to the inside, make two or three small stitches in the same spot, and cut the thread. A tiny dab of clear fabric glue on the knot stops it from coming undone.

Common mistakes

  • Pulling too tight. It puckers the fabric. Stitches should lie flat.
  • Using the wrong thread color. Match the border so the stitches disappear.
  • Skipping the pins. The patch shifts as you sew and ends up crooked.
  • Sewing stretchy fabric flat. On knits, stitch loosely so the fabric can still stretch.

Sew-on, iron-on or velcro?

If the garment gets washed often or worked hard, sewing wins. If you want it on quickly, read our guide to ironing on a patch. If you want to swap patches, choose velcro patches. Our comparison, iron-on, sew-on or velcro, covers the trade-offs in detail.

Ordering patches that are easy to sew

Every patch we make can be sewn on. Choose a merrow or embroidered border for the cleanest edge to stitch through. You can order from just 5 pieces, see your price instantly and get a free mockup before anything is made.

Patches mentioned in this guide

Iron-on patches · Jacket patches

Ready to order custom patches?

See your price instantly. Get a free mockup in 12 to 24 hours. Nothing is made until you approve it.

Get an instant price